OBJECTIVES WITH MAGNETIC CONNECTION
FOR CAPILLAROSCOPY AND DERMATOLOGY
![]() |
||
Objectives' code |
Magnification (referred to a 14" monitor) |
Field of view (mm) ![]() MONITOR |
VMC - 8,3 | 8,3X |
33x25 |
VMC - 15 | 15X |
16x12,5 |
VMC - 20 | 20X |
14x11 |
VMC - 35 | 35X |
8x6 |
VMC - 50 | 50X |
5,5x4,3 |
VMC - 75 | 75X |
4x3 |
VMC - 90 | 90X |
3x2,3 |
º CMS - 150 | 150X |
1,8x1,4 |
VMC - 200 | 200X |
1,2x0,9 |
º CMS - 250 | 250X |
1,1x0,83 |
º CMS - 450 | 450X |
0,6x0,45 |
º CMS - 750 | 750X |
0,36x0,27 |
Dermatology objectives |
º Capillaroscopy objectives |
The Capillaroscope can be used with low magnification objectives (wide field of view - dermatology) and with high magnification objectives (for capillaroscopy).
The change of the objectives is very simple and fast because they are equipped with magnetic connection, therefore it will be enough a light downward force to remove and replace them.
While the objectives for dermatology have a wider base of support, the objectives for capillaroscopy are designed to be used on the restricted epidermal surfaces (eg. between two fingers, etc.); these ones, for be used, shall be coupled to the light conveyor that also has the function of support base.
All the objectives are protected at the base by a special protective glass allowing the use for contact of several types of oils used in dermatology and capillaroscopy (immersion oil, oil of cedar, etc.).
Note that using the right type of objective is matter of personal experience, however it's good to know that high magnification objectives (eg. 450X-750X) should be used with steady hand and exerting slow steady pressure with the device on the surface to inspect in order to avoid focusing in continuation with the metal ring of the capillaroscope.
If you want to acquire the face of your patient and save it in a database, you can use the objective VMC-8,3. By placing vertically the capillaroscope in one hand to about 50 cm from your subject's face (adequately illuminated) and focusing with the metal ring, the capture of the image can be done by pressing the button on the handle of the device or through a pedal connected on the console of the suitcase.
The change of the objectives is very simple and fast because they are equipped with magnetic connection, therefore it will be enough a light downward force to remove and replace them.
While the objectives for dermatology have a wider base of support, the objectives for capillaroscopy are designed to be used on the restricted epidermal surfaces (eg. between two fingers, etc.); these ones, for be used, shall be coupled to the light conveyor that also has the function of support base.
![]() |
---|
Note that using the right type of objective is matter of personal experience, however it's good to know that high magnification objectives (eg. 450X-750X) should be used with steady hand and exerting slow steady pressure with the device on the surface to inspect in order to avoid focusing in continuation with the metal ring of the capillaroscope.
If you want to acquire the face of your patient and save it in a database, you can use the objective VMC-8,3. By placing vertically the capillaroscope in one hand to about 50 cm from your subject's face (adequately illuminated) and focusing with the metal ring, the capture of the image can be done by pressing the button on the handle of the device or through a pedal connected on the console of the suitcase.
STAND FOR CAPILLAROSCOPE
![]() |
![]() |
![]() |