EXPLORAR
Lupes, Linsen

PEAK TELECENTRIC LUPE 7X

   This is a special purpose loupe with a magnifying power of 7 times. It belongs to the category of scale-loupes with an affixed transparent glass scale which can be placed in contact with the object under examination, so that you can measure the length of the object very easily and accurately. However, the magnifying optical system of this loupe is not conventional, but is "telecentric", i.e. characterized by a small opening fixed at the focal point of the lens system, through which you can measure the length or width of not only flat objects, but also three-dimensional ones such as small spheres, cylinders etc. without the error caused by parallax. This handy instrument is equivalent in its principle to expensive profile projectors. The lens system, composed of three elements in two groups, has been specially designed for the present purpose. 
   To use the loupe, first adjust the distance between the glass scale and the lens system by turning the knurled outer barrel until the scale can be sharply observed by your own eye through the opening with the largest diameter (3 mm), which can be selected simply by turning the turret ring at the top of the loupe. Then place the loupe upon the object to be measured so that the scale plate is in contact with it, and read its length by the scale. The scale is engraved 20 mm in total length at every 0.1 mm interval, so you can measure the length of objects with an error of less than 0.03 mm.
   When measuring three-dimensional objects. the opening with the minimum diameter (1 mm), or preferably the one with a slit of 0.5 mm in width should be used; and the orientation of the slit should kept perpendicular to the direction along which the length of the object is to be measured. Even in these cases, the portions of the object that are not in contact with the scale plate may be fuzzy because they are out of focus. However, no error can occur in the measured length, as long as you measure the centre-to-centre distance of blurred images, thanks to the characteristic of the "tele­centric" system. The low brightness of the image due to the small openings can be compensated for by higher illumination of the object.
   This loupe can be applied very effectively as a reading aid for mercury thermometers. By putting the end surface of the transparent tube of the loupe (the scale plate of which should, preferably, be taken off) correctly against the thermometer tube, you can read the temperature extremely accurately and without any parallax, even if the mercury thread and the temperature scale are not in the same plane. The slit-form opening is used very effectively in this case, with its orientation kept parallel to the engraved lines of the ther­mometer scale. (Care should be taken that your body temperature does not affect the temperature to be measured.) Also, by replacing the transparent tube of the loupe with a tube of the proper length and by putting its end surface squarely on the window of voltmeters etc., you can read the indication of the meter needle very accurately and without any parallax.

1999

Telecentric Lupe 7X

Magnification:
-
7X
Field of view:
-
24 mm
Size:
-
38ø x 74 mm
Net weight:
-
73 g
Scale length:
-
20 mm
Min. Scale Division:
-
0,1 mm


PEAK POCKET MICROSCOPE

   The main features of this Pocket Microscope are: very sharp resolution power throughout its field of view, unbelievably brightness and light weight. It is a practical and convenient pocket microscope for technicians and engineers.
   To focus the microscope, hold it so that the notch at the tip of the acryl cylinder of the microscope will face towards you, place the centre of the object lens right above the specimen and, while tilting the cylinder forward and backward with your eye on the eye-piece lens, fix the cylinder and observe at an angle which can give the sharpest image.
   Similar to the pocket microscopes of the 2001 series, the 2001 long is characterized by a barrel longer than the previous one and this feature allows to adopt a comfortable and sitting posture while you observe an object.

Derived from the 2001 Long, the Optic Light 100-90 Borescope (2001-OLB) allows the vision at 90° of particular in areas difficult to reach with the help of its particular lighting.


2001

2001 Long
Pocket Microscope





Pocket Microscope

 

  Item No.
2001-15
2001-15 Long
2001-25
Magnification
15X
15X
25X
Field of view
5.40 mm ø
5.40 mm ø
3.30 mm ø
Size (mm)
12.4øx127
12.4øx180
12.4øx127
Net weight
13 g
18 g
12 g
Item No.
2001-50
2001-75
2001-100
Magnification
50X
75X
100X
Field of view
2.00 mm ø
1.09 mm ø
0.84 mm ø
Size (mm)
12.4øx127
12.4øx127
12.4øx127
Net weight
12 g
13 g
16 g
             

2001-L
Pocket Microscope with led light
  Item No.
2001-15-L
2001-25-L
2001-50-L
2001-75-L
2001-100-L
as 2001 but with
additional led light
             



2001-OLB

Optic Light
100-90 Borescope 15X

   
Item No.
2001-OLB
   
Magnification
15X
   
Field of view
5.40 mm ø
   
Size (mm)
12.4øx180
   
Net weight
150 g
   
For more details click here
   See also: 2008 / 2036 / 2050 / 2051 / 2056 / 3703

PEAK LINEN TESTER

   Peak Linen Testers are convenient folding type magnifying glasses for inspecting cloth. They are widely used as portable magnifiers and are available in the various models shown in the following table.

2003WA3 1504WA3 1006WZ3 3408WZ3
1209WZ3 1006SA3
1006SA3 LO*
3407SA3
3407SA3 LO*
1209SA3


Item Base size (in.) Base size (mm) Magnification Lens element Material Surface treatment
1209SA3 1/2 10 9X 1 Aluminium Black
3407SA3 3/4 15 7X 1 Aluminium Black
1006SA3 1 25 6X 1 Aluminium Black
1209WZ3 1/2 10 9X 2 Zinc Black
3408WZ3 3/4 15 8X 2 Zinc Black
1006WZ3 1 25 6X 2 Zinc Black
1504WA3 30 4X 2 Aluminium Black
2003WA3 2 50 3X 2 Aluminium Black

(*): Customized with your logo

 

Explanation of article description
*     First two numbers of four show the length of base on which each scale is marked
       (e.g. 12=1/2", 34=3/4",10=1").
*     Last two numbers of four show the magnification (e.g. 09=9X, 07=7X).
*     S shows single lens and W shows double lenses.
*     A shows frame of aluminium and Z shows of zinc.
*     The last number shows the surface treatment of metal frame (e.g. 0=silver paint, 3=black paint).
 

   See also: 2052

 

LINEN TESTERS


2003-6M
2003-6M LO*
2003-8CU 2003-10M 2003-8P
   
 
Code Field of measure Magnification n° lens Material Color Pouche Min.order
quantity
2003-6M* 20mm 1" 6X 1 Metal Black Plastic 5
2003-8CU 20mm (scala 1/10mm) 8X 2 Copper Silver Plastic 1
2003-10M 12mm 1/2" 10X 1 Metal Black Plastic 5
2003-8P 20mm 3/4" 8X 1 Plastic Black - 5

(*): Customized with your logo

2003-TEXILLED

2003-6MLED
2003-6MLEDLO*

 




2003-5P BLACK
2003-5P BLACK LO
*

2003-5P WHITE
2003-5P WHITE LO
*

 
Code Field of measure Magnification n° lens Material Color Pouche Min.order
quantity
2003-5P BLACK* 30mm 1" 5X 1 Plastic Black - 5
2003-5P WHITE* 30mm 5X 5X 1 Plastic White - 5
2003-TEXILLED 20mm 1/2" 6X 1 Metal Black Plastic 2
2003-6MLED* 25mm 3/4" 6X 1 Metal Black Leather 5

(*): Customized with your logo